ADV7181

Video A/D-Wandler, verbaut in Navigationssystemen mit Videoeingang für Rückfahrkamera.

Fotos und Position

Technische Daten

Blockdiagramm und typisches Anwendungsbeispiel

Pinout

Programmierung

Initialisierung durch Cyclone III FPGA auf MCA-Plus Grafikboard

IDENT

Das IDENTITY-Register 0x11 gibt bei diesem Chip den Wert 0x19 zurück. Die Software verwendet den Zugriff darauf um zu prüfen ob der Chip antwortet, vorhanden oder bereits aus einem RESET zurückgekehrt ist.

  1. 20 11 19

RESET

  1. 40 0F 80 = Store 0x80 into register 0x0F = Start reset sequence (takes approx. 2 ms)

SETUP 1

  1. 40 07 7B ⇒ Set Autodetect Enable Register 0x07 to 0b0111_1011
    • Detect PAL B/G/I/H, PAL N, PAL 60, NTSC, NTSC443 formats
  2. 40 15 00 ⇒ Set Digital Clamp Control 1 Register 0x15 to 0b0000_0000
    • Slow (TC = 1 s)
  3. 40 17 41 ⇒ Set Shaping Filter Control Register 0x17 to 0b0100_0001
    • Auto narrow notch for poor quality sources or wideband filter with comb for good quality input. Select Chrominance Filter „SH1“ for all video standards and for good and bad video.
  4. 40 1D 40 ⇒ Set UNKNOWN Register 0x1D to 0b0100_0000
  5. 40 0F 40 ⇒ Set Power Management Register 0x0F to 0xb0100_0000
    • RESERVED VALUE IN DATASHEET
  6. 40 3A 16 ⇒ Set ADC Control Register 0x3A to 0b0001_0110
    • Power down ADC2
    • Power down ADC1
    • Set ADC0 to normal operation
  7. 40 3D C3 ⇒ Set Manual Window Register 0x3D to 0b1100_0011
    • Kill at 8.5%
  8. 40 3F E4 ⇒ Set UNKNOWN Register 0x3F to 0b1110_0100
  9. 40 50 04 ⇒ Set CTI DNR Control 4 Register 0x50 to 0b0000_0100
    • Set to 0x04 for A/V input
  10. 40 51 2D ⇒ Set Lock Count Register 0x51 to 0b0_0_101_101
    • Count-into-lock = 500 lines of video
    • Count-out-of-lock = 500 lines of video
    • Over field with vertical info
    • Lock status set only by horizontal lock
  11. 40 C4 80 ⇒ Set ADC SWITCH 2 Register 0xC4 to 0b1_000_0000
    • Enable manual setting of the input signal muxing
  12. 40 0E 80 ⇒ Set ADI Control Register 0x0E to 0b1_1_00_00_00
    • Set sync signals to „Low drive strength (1x)“
    • Set clock signal to „Low drive strength (1x)“
    • Enable LLC pin to be three-stated
  13. 40 50 20 ⇒ Set CTI DNR Control 4 Register 0x50 to 0b0010_0000 (ILLEGAL: VALUE)
  14. 40 52 18 ⇒ Set UNKNOWN Register 0x52 to 0b0001_1000
  15. 40 58 ED ⇒ Set UNKNOWN Register 0x58 to 0b1110_1101
  16. 40 77 C5 ⇒ Set UNKNOWN Register 0x77 to 0b1100_0101
  17. 40 7C 93 ⇒ Set UNKNOWN Register 0x7C to 0b1001_0011
  18. 40 7D 00 ⇒ Set UNKNOWN Register 0x7D to 0b0000_0000
  19. 40 90 C9 ⇒ Set VBI Info Read Mode Details Register 0x90 to 0b1100_1_0_0_1 (ILLEGAL: READ ONLY)
  20. 40 91 40 ⇒ Set WSS1 Register 0x91 to 0b0100_0000 (ILLEGAL: READ ONLY)
  21. 40 92 3C ⇒ Set WSS2 Register 0x92 to 0b0011_1100 (ILLEGAL: READ ONLY)
  22. 40 93 CA ⇒ Set EDTV1 Register 0x93 to 0b0011_1100 (ILLEGAL: READ ONLY)
  23. 40 94 D5 ⇒ Set EDTV2 Register 0x94 to 0b1101_0101 (ILLEGAL: READ ONLY)
  24. 40 CF 50 ⇒ Set UNKNOWN Register 0xCF to 0b0101_0000
  25. 40 D0 4E ⇒ Set UNKNOWN Register 0xD0 to 0b0100_1110
  26. 40 D6 DD ⇒ Set UNKNOWN Register 0xD6 to 0b1101_1101
  27. 40 E5 51 ⇒ Set NTSC V Bit Begin Register 0xE5 to 0b0_1_0_10001
    1. Set „V“ high after 30 lines from „Icount“ rollover (default: 5 lines)
    • Set „NVBEGSIGN“ to low
    • Set „NVBEGDELE“ to additional delay by 1 line
    • Set „NVBEGDELO“ to no delay
  28. 40 D5 A0 ⇒ Set UNKNOWN Register 0xD5 to 0b1010_0000
  29. 40 D7 EA ⇒ Set UNKNOWN Register 0xD7 to 0b1110_1010
  30. 40 E4 3E ⇒ Set SD Saturation Cr Register 0xE4 to 0b0011_1110
  31. 40 E9 3E ⇒ Set PAL V Bit End Register 0xE9 to 0b0_0_1_11110
    • Set „V“ high after 30 lines from „Icount“ rollover (default: 5 lines)
    • Set „PVENDSIGN“ to 1
    • Set „PVENDDELE“ to no delay
    • Set „PVENDDELO“ to no delay
  32. 40 EA 0F ⇒ Set PAL F Bit Toggle Register 0xEA to 0b0_0_0_01111
    • Set toggle „F“ signal after 15 lines after „Icount“ rollover (default: 3 lines)
    • Set to „PFTOGSIGN“ to low
    • Set „PFTOGDELE“ to no delay
    • Set „PFTOGDELO“ to no delay
  33. 40 0E 00 ⇒ Set ADI Control Register 0x0E to 0b0_0_00_00_00
    • Set „DR_STR_S“ to Low drive strength
    • Set „DR_STR_C“ to Low drive strength
    • Set LLC pin active
  34. 40 C3 06 ⇒ Set ADC SWITCH 1 Register 0xC3 to 0b0000_0110
    • No input selected
  35. 40 0A 0A ⇒ Set Brightness Register 0x0A to 0b0000_1010
    • 0x0A equals „8 IRE“
  36. 20 11 19 ⇒ Read IDENT Register 0x11 having value 0b0001_1001

SETUP 2

Nach der Squenz „SETUP 1“ folgt dieselbe Sequenz erneut, wird aber durch folgende ergänzt:

  1. 40 0E 20 ⇒ Set ADI Control Register 0x0E to 0b0_0_10_00_00
    • Set LLC pin to „three-stated“
  2. 40 4C 02 ⇒ Set Gemstar Control 5 Register 0x4C to 0b0000001_0
    • Split data into half byte
  3. 40 40 D2 ⇒ Set UNKNOWN Register 0x40 to 0b1101_0010
  4. 40 0E 00 ⇒ Set ADI Control Register 0x0E to 0b0_0_00_00_00
    • Set LLC pin to „active“
  5. 40 0E 20 ⇒ Set ADI Control Register 0x0E to 0b0_0_10_00_00
    • Set LLC pin to „three-stated“
  6. 40 4B 02 ⇒ Set Gemstar Control 4 Register 0x4B to 0b0000001_0
  7. 40 0E 00 ⇒ Set ADI Control Register 0x0E to 0b0_0_00_00_00
    • Set LLC pin to „active“
  8. 20 11 19 ⇒ Read IDENT Register 0x11 with value 0b0001_1001
  9. 40 0E 20 ⇒ Set ADI Control Register 0x0E to 0b0_0_10_00_00
    • Set LLC pin to „three-stated“
  10. 20 49 06 ⇒ Read Gemstar Control 2 Register 0x49 having value 0b0000_0110
  11. 40 0E 00 ⇒ Set ADI Control Register 0x0E to 0b0_0_00_00_00
    • Set LLC pin to „active“
  12. 20 10 0F ⇒ Read Status Register 0x10 having value 0b0000_1111
  13. 20 13 29 ⇒ Read Status Register 3 Register 0x13 having value 0b0010_1001
  14. 20 0A 00 ⇒ Read Brightness Register 0x0A having value 0b0000_0000
  15. 20 08 80 ⇒ Read Contrast Register 0x08 having value 0b1000_0000
    • Gain = 1 dB
  16. 20 0B 00 ⇒ Read Hue Register 0x0B having value 0b0000_0000
  17. 20 E3 80 ⇒ Read SD Saturation Cb having value 0b1000_0000
    • Chroma gain = 0 dB

Fundort im Flash-Memory des Graphicboard

Tatsächlich liegen diese Sequenzen fest vorgegeben im Flash auf dem Graphicboard und im „fgs.dnl“ File der Update-CD: 

Offset(h) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

0007AEF0  40 07 7B 40 15 00 40 17 41 40 1D 40 40 0F 40 40  @.{@..@.A@.@@.@@
0007AF00  3A 16 40 3D C3 40 3F E4 40 50 04 40 51 2D 40 C4  :.@=Ã@?ä@P.@Q-@Ä
0007AF10  80 40 0E 80 40 50 20 40 52 18 40 58 ED 40 77 C5  €@.€@P @R.@Xí@wÅ
0007AF20  40 7C 93 40 7D 00 40 90 C9 40 91 40 40 92 3C 40  @|“@}.@.É@‘@@’<@
0007AF30  93 CA 40 94 D5 40 CF 50 40 D0 4E 40 D6 DD 40 E5  “Ê@”Õ@ÏP@ÐN@ÖÝ@å
0007AF40  51 40 D5 A0 40 D7 EA 40 E4 3E 40 E9 3E 40 EA 0F  Q@Õ @×ê@ä>@é>@ê.
0007AF50  40 0E 00 40 00 05 40 03 0C 40 04 77 40 17 41 40  @..@..@..@.w@.A@
0007AF60  1D 47 40 31 02 40 3A 17 40 3B 81 40 3D A2 40 3E  .G@1.@:.@;.@=¢@>
0007AF70  6A 40 3F A0 40 86 0B 40 F3 01 40 F9 03 40 0E 80  j@? @†.@ó.@ù.@.€
0007AF80  40 52 46 40 54 00 40 7F FF 40 81 30 40 90 C9 40  @RF@T.@.ÿ@.0@.É@
0007AF90  91 40 40 92 3C 40 93 CA 40 94 D5 40 B1 FF 40 B6  ‘@@’<@“Ê@”Õ@±ÿ@¶
0007AFA0  08 40 C0 9A 40 CF 50 40 D0 4E 40 D1 B9 40 D6 DD  .@Àš@ÏP@ÐN@ѹ@ÖÝ
0007AFB0  40 D7 E2 40 E5 51 40 F6 3B 40 0E 00 40 01 C8 40  @×â@åQ@ö;@..@.È@
0007AFC0  05 00 40 06 0E 40 1D 40 40 0F 40 40 31 02 40 3A  ..@..@.@@.@@1.@:
0007AFD0  10 40 3D C3 40 3F E4 40 52 00 40 53 00 40 54 07  .@=Ã@?ä@R.@S.@T.
0007AFE0  40 55 0C 40 56 94 40 57 89 40 58 48 40 59 08 40  @U.@V”@W‰@XH@Y.@
0007AFF0  5A 00 40 5B 7A 40 5C E1 40 5D 00 40 5E 19 40 5F  Z.@[z@\á@].@^.@_
0007B000  48 40 60 08 40 61 00 40 62 20 40 63 03 40 64 A9  H@`.@a.@b @c.@d©
0007B010  40 65 1A 40 66 B8 40 67 03 40 68 00 40 6A 80 40  @e.@f¸@g.@h.@j€@
0007B020  6B C3 40 73 D0 40 74 B4 40 7B 06 40 C3 C9 40 C4  kÃ@sÐ@t´@{.@ÃÉ@Ä
0007B030  8D 40 85 1A 40 86 02 40 B3 FE 40 C9 0C 40 0E 80  .@….@†.@³þ@É.@.€
0007B040  40 58 ED 40 90 C9 40 91 40 40 92 3C 40 93 CA 40  @Xí@.É@‘@@’<@“Ê@
0007B050  94 D5 40 CF 7C 40 D0 4E 40 D6 DD 40 E5 51 40 0E  ”Õ@Ï|@ÐN@ÖÝ@åQ@.
Offset(h) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F

004E1090                                      40 07 7B 40              @.{@
004E10A0  15 00 40 17 41 40 1D 40 40 0F 40 40 3A 16 40 3D  ..@.A@.@@.@@:.@=
004E10B0  C3 40 3F E4 40 50 04 40 51 2D 40 C4 80 40 0E 80  Ã@?ä@P.@Q-@Ä€@.€
004E10C0  40 50 20 40 52 18 40 58 ED 40 77 C5 40 7C 93 40  @P @R.@Xí@wÅ@|“@
004E10D0  7D 00 40 90 C9 40 91 40 40 92 3C 40 93 CA 40 94  }.@.É@‘@@’<@“Ê@”
004E10E0  D5 40 CF 50 40 D0 4E 40 D6 DD 40 E5 51 40 D5 A0  Õ@ÏP@ÐN@ÖÝ@åQ@Õ 
004E10F0  40 D7 EA 40 E4 3E 40 E9 3E 40 EA 0F 40 0E 00 40  @×ê@ä>@é>@ê.@..@
004E1100  00 05 40 03 0C 40 04 77 40 17 41 40 1D 47 40 31  ..@..@.w@.A@.G@1
004E1110  02 40 3A 17 40 3B 81 40 3D A2 40 3E 6A 40 3F A0  .@:.@;.@=¢@>j@? 
004E1120  40 86 0B 40 F3 01 40 F9 03 40 0E 80 40 52 46 40  @†.@ó.@ù.@.€@RF@
004E1130  54 00 40 7F FF 40 81 30 40 90 C9 40 91 40 40 92  T.@.ÿ@.0@.É@‘@@’
004E1140  3C 40 93 CA 40 94 D5 40 B1 FF 40 B6 08 40 C0 9A  <@“Ê@”Õ@±ÿ@¶.@Àš
004E1150  40 CF 50 40 D0 4E 40 D1 B9 40 D6 DD 40 D7 E2 40  @ÏP@ÐN@ѹ@ÖÝ@×â@
004E1160  E5 51 40 F6 3B 40 0E 00 40 01 C8 40 05 00 40 06  åQ@ö;@..@.È@..@.
004E1170  0E 40 1D 40 40 0F 40 40 31 02 40 3A 10 40 3D C3  .@.@@.@@1.@:.@=Ã
004E1180  40 3F E4 40 52 00 40 53 00 40 54 07 40 55 0C 40  @?ä@R.@S.@T.@U.@
004E1190  56 94 40 57 89 40 58 48 40 59 08 40 5A 00 40 5B  V”@W‰@XH@Y.@Z.@[
004E11A0  7A 40 5C E1 40 5D 00 40 5E 19 40 5F 48 40 60 08  z@\á@].@^.@_H@`.
004E11B0  40 61 00 40 62 20 40 63 03 40 64 A9 40 65 1A 40  @a.@b @c.@d©@e.@
004E11C0  66 B8 40 67 03 40 68 00 40 6A 80 40 6B C3 40 73  f¸@g.@h.@j€@kÃ@s
004E11D0  D0 40 74 B4 40 7B 06 40 C3 C9 40 C4 8D 40 85 1A  Ð@t´@{.@ÃÉ@Ä.@….
004E11E0  40 86 02 40 B3 FE 40 C9 0C 40 0E 80 40 58 ED 40  @†.@³þ@É.@.€@Xí@
004E11F0  90 C9 40 91 40 40 92 3C 40 93 CA 40 94 D5 40 CF  .É@‘@@’<@“Ê@”Õ@Ï
004E1200  7C 40 D0 4E 40 D6 DD 40 E5 51 40 0E 00 00 00 00  |@ÐN@ÖÝ@åQ@.....