Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- artikel:ipc:mac7116 [Mon. 01.04.2019 04:11] – go4it
+++ artikel:ipc:mac7116 [Mon. 01.04.2019 04:13] – [Init procedure] go4it
@@ Zeile 106: / Zeile 106: @@
 https://www.nxp.com/part/MAC7116VAG50
+=== DEFs ===
 <code>
@@ Zeile 124: / Zeile 126: @@
 cfmdfdacc       MM	0xFC0F0046	8
 </code>
+=== Segger ===
 <code>
@@ Zeile 133: / Zeile 137: @@
 mem16 fe000000,1 // verify writing->FE000000=FFFF // write fault
 </code>
+=== PEEDI ===
+<code>
+;-------------------------------------------------------------------------------
+;
+;
+;   PEEDI target configuration file for Freescale MAC7100 processor
+;
+;   Ronetix
+;
+;   Supported devices   : MAC7100
+;
+;   Revision            : 1.5
+;
+;   Date                : March 23, 2007
+;
+; The software is delivered "AS IS" without warranty or condition of any
+; kind, either express, implied or statutory. This includes without
+; limitation any warranty or condition with respect to merchantability or
+; fitness for any particular purpose, or against the infringements of
+; intellectual property rights of others.
+;
+;-------------------------------------------------------------------------------
+;--------------------------------------------------------------------------
+; The following section contains licenses that are required for PEEDI to
+; operate. These licenses must be filled before using this file.
+; The [LICENSE] section may contain license keys for one or more PEEDIs.
+;
+;   Example:
+;       [LICENSE]
+;       KEY         = UPDATE_24MAY2010, 1111-1111-1111-1
+;       KEY         = XXXXX, 2222-2222-2222-2
+;
+; The [LICENSE] section may point to an external file which contains
+; license keys for one or more PEEDIs. The external file must include
+; the text [LICENSE] followed by all keys.
+;
+;   Example:
+;		[LICENSE]
+;		FILE = tftp://192.168.3.1/license.txt
+;		or
+;		FILE=eep:license.txt
+;		or
+;		FILE = ftp://user:password@192.168.3.1/license.txt
+;
+;
+; PEEDI is shipped with license keys stored in "eep:license.txt" and
+; printed on a label on the bottom side of PEEDI.
+;
+[LICENSE]
+FILE=eep:license.txt
+;--------------------------------------------------------------------------
+[DEBUGGER]
+PROTOCOL            = gdb_remote            ; gdb remote
+REMOTE_PORT         = 2000                  ; TCP/IP port
+[TARGET]
+PLATFORM            = ARM                   ; platform is ARM
+[PLATFORM_ARM]
+JTAG_CHAIN          = 4                     ; list of IR length of all TAP controller in JTAG chain
+JTAG_CLOCK          = 20, 4000              ; JTAG Clock in [kHz] - 10kHz jtag clock for init operations and 4MHz for normal work
+                                            ; Freescale recommends max JTAG_CLOCK 1/6 of the system clock
+TRST_TYPE           = OPENDRAIN             ; type of TRST output: OPENDRAIN or PUSHPULL
+RESET_TIME          = 20                    ; 20ms reset pulse, 0 means no reset
+TIME_AFTER_RESET    = 100                   ; time between releasing the reset and starting the jtag communication
+CORE0               = MAC7100               ; TAP is Freescale MAC71xx  CPU
+CORE0_STARTUP_MODE  = RESET                 ; startup mode after reset:
+                                            ;   if RESET than no code is executed after reset
+                                            ;   if STOP,XX then the target executes code for XX period in ms.
+                                            ;   if RUN then the target executes code until stopped by the telnet "halt" command
+CORE0_BREAKMODE         = soft              ; breakpoint mode:
+                                            ; soft - software breakpiont
+                                            ; hard - use hardware breakpoints instead of software
+CORE0_BREAK_PATTERN     = 0xDFFFDFFF        ; software breakpoint pattern
+CORE0_INIT              = INIT_MAC7100      ; init section for MAC7100 board
+CORE0_FLASH0            = FLASH_PROG        ; PROGRAM flash section parameters
+CORE0_ENDIAN            = BIG               ; core is big endian
+CORE0_WORKSPACE_ADDR    = 0x40000100        ; start address of workspace for flash programmer
+CORE0_WORKSPACE_LEN     = 0x4000            ; length of workspace in bytes
+CORE0_LOCKOUT_RECOVERY  = 19                ; If this parameter is present, PEEDI automatically executes a
+                                            ; "JTAG Lockout Recovery" procedure during reset processing
+                                            ; if the MAC7100 flash is secured
+                                            ; Fsys 4MHz CLKD=9; Fsys 8MHz CLKD=19
+CORE0_FILE              = "myfile.bin", BIN, 0x40000100 ; default file
+CORE0_PATH              = "tftp://192.168.3.1" ; default path
+[INIT_MAC7100]
+memory write8  0xfc088004 0     ; CRGINT Disable clock interrupts
+; Speed-up to fsys = 50MHz, Fsys = 2*Fosc*(mul/div)
+; Quartz is 8.00 MHz
+;--------------------------------------------------
+memory write8  0xfc088001 0x07          ; REFDV - CRG Reference Divider register - divide by 8
+memory write8  0xfc088000 0x18          ; SYNR - CRG synthesizer Register - multiply by 25
+wait 10
+memory write8  0xfc088005 0x80          ; CLKSEL - Select fsys=PLLCLK
+memory write8  0xFC088003 0x72          ; clear the flags
+memory write8  0xfc088008 0x00          ; BDMCTL - SWT and RTI keep running in debug mode
+memory write16 0xfc0e80c4 0x0080        ; output CLKOUT on PD2
+set pc 0x40000000                       ; set PC to RAM memory base
+[FLASH_PROG]
+CHIP                = MAC7100           ; flash chip
+CPU_CLOCK           = 50000             ; PLL clock
+CHECK_ID            = YES
+FILE                = "myprog.bin", BIN, 0xFC100000 ; file to program
+AUTO_ERASE          = NO               ; erase before program
+[SERIAL]                                ; serial port configuration
+BAUD                = 115200
+STOP_BITS           = 1
+PARITY              = NONE
+TCP_PORT            = 0                 ; enable CLI over RS232
+;TCP_PORT           = 2023              ; enable serial over TCP/IP
+[TELNET]
+PROMPT              = "MAC7100> "       ; telnet prompt
+;BACKSPACE          = 127               ; comment out for autodetect
+[DISPLAY]
+BRIGHTNESS          = 20                ; LED indicator brightness
+VOLUME              = 25                ; zummer volume
+[ACTIONS]                               ; user defined scripts
+= erase
+= prog
+= dump_ram
+= dump_flash
+[erase]                                 ; erase flash
+flash erase
+[prog]                                  ; program flash
+flash prog
+</code>
+=== ... ===
 <code>