Code | Meaning | Bedeutung |
00 | „No sub type information“ | Keine weiteren Fehlerinformationen vorhanden |
01 | „General electrical failure“ | Allgemeines, elektrisches Problem |
02 | „General signal failure“ | |
03 | „FM (Frequency Modulated)/PWM (Pulse Width Modulated) failures“ | |
04 | „System internal failures“ | |
05 | „System programming failures“ | |
06 | „Algorithm based failures“ | |
07 | „Mechanical failures“ | |
08 | „Bus signal/message failures“ | |
09 | „Component failures“ | |
11 | „Circuit short to ground“ | |
12 | „Circuit short to battery“ | |
13 | „Circuit open“ | |
14 | „Circuit short to ground or open“ | |
15 | „Circuit short to battery or open“ | |
16 | „Circuit voltage below threshold“ | |
17 | „Circuit voltage above threshold“ | |
18 | „Circuit current below threshold“ | |
19 | „Circuit current above threshold“ | |
1A | „Circuit resistance below threshold“ | |
1B | „Circuit resistance above threshold“ | |
1C | „Circuit voltage out of range“ | |
1D | „Circuit current out of range“ | |
1E | „Circuit resistance out of range“ | |
1F | „Circuit intermittent“ | |
20 | „Reserved by document“ | |
21 | „Signal amplitude < minimum“ | |
22 | „Signal amplitude > maximum“ | |
23 | „Signal stuck low“ | |
24 | „Signal stuck high“ | |
25 | „Signal shape/waveform failure“ | |
26 | „Signal rate of change below threshold“ | |
27 | „Signal rate of change above threshold“ | |
28 | „Signal bias level out of range/zero adjustment failure“ | |
29 | „Signal signal invalid“ | |
2A | „Signal stuck in range“ | |
2B | „Signal cross coupled“ | |
2F | „Signal erratic“ | |
30 | „Reserved by document“ | |
31 | „No signal“ | |
32 | „Signal low time < minimum“ | |
33 | „Signal low time > maximum“ | |
34 | „Signal high time < minimum“ | |
35 | „Signal high time > maximum“ | |
36 | „Signal frequency too low“ | |
37 | „Signal frequency too high“ | |
38 | „Signal frequency incorrect“ | |
39 | „Incorrect has too few pulses“ | |
3A | „Incorrect has too many pulses“ | |
40 | „Reserved by document“ | |
41 | „General checksum failure“ | |
42 | „General memory failure“ | |
43 | „Special memory failure“ | |
44 | „Data memory failure“ | |
45 | „Program memory failure“ | |
46 | „calibration/parameter memory failure“ | |
47 | „Watchdog/safety microcontroller failure“ | |
48 | „Supervision software failure“ | |
49 | „Internal electronic failure“ | |
4A | „Incorrect component installed“ | |
4B | „Over temperature“ | |
50 | „Reserved by document“ | |
51 | „Not programmed“ | |
52 | „Not activated“ | |
53 | „Deactivated“ | |
54 | „Missing calibration“ | |
55 | „Not configured“ | |
56 | „Invalid/incomplete configuration“ | |
57 | „Invalid/incomplete software component“ | |
60 | „Reserved by document“ | |
61 | „Signal calculation failure“ | |
62 | „Signal compare failure“ | |
63 | „Circuit / component protection time-out“ | |
64 | „Signal plausibility failure“ | |
65 | „Signal has too few transitions / events“ | |
66 | „Signal has too many transitions / events“ | |
67 | „Signal incorrect after event“ | |
68 | „Event information“ | |
70 | „Reserved by document“ | |
71 | „Actuator stuck“ | |
72 | „Actuator stuck open“ | |
73 | „Actuator stuck closed“ | |
74 | „Actuator slipping“ | |
75 | „Emergency position not reachable“ | |
76 | „Wrong mounting position“ | |
77 | „Commanded position not reachable“ | |
78 | „Alignment or adjustment incorrect“ | |
79 | „Mechanical linkage failure“ | |
7A | „Fluid leak or seal failure“ | |
7B | „Low fluid level“ | |
80 | „Reserved by document“ | |
81 | „Invalid serial data received“ | |
82 | „Alive/sequence counter incorrect/not updated“ | |
83 | „Value of signal protection calculation incorrect“ | |
84 | „Signal below allowable range“ | |
85 | „Signal above allowable range“ | |
86 | „Signal invalid“ | |
87 | „Missing message“ | |
88 | „Bus off“ | |
8F | „Erratic“ | |
90 | „Reserved by document“ | |
91 | „Parametric“ | |
92 | „Performance or incorrect operation“ | |
93 | „No operation“ | |
94 | „Unexpected operation“ | |
95 | „Incorrect assembly“ | |
96 | „Component internal failure“ | |
97 | „Component or system operation obstructed or blocked“ | |
98 | „Component or system over temperature“ | |
9A | „Component or system operating conditions“ | |